The aluminium windows and doors factory

One site, one quality gate — the factory behind every system on the line card.

Sashes leave the line factory-assembled and pre-glazed — the tolerance work is done under a roof, not on your job site.

30,000 m²
Manufacturing base, Foshan
42,000+
Projects supplied
100+
Countries served
2006
Established

The factory sits inside a Foshan building-materials group founded in 2006. Who the company is, what it holds and how the division is structured is set out on the about the factory division, including the group registration details and the product scope each entity covers.

CNC machining centre cutting an aluminium profile at the Foshan plant
The CNC line — profiles cut, milled and drilled before assembly
The anodising line — profiles through the oxidation bath
The anodising line — profiles oxidised and finished to colour

The section, up close

Every system is built on multi-chamber 6063-T5 extrusion with a continuous PA66 thermal-break bar and two replaceable EPDM gasket lines. The values in the performance band on the home page are read off this section — here it is, photographed.

Multi-chamber 6063-T5 frame profile cross section with continuous thermal break
Frame profile cross section — three internal chambers for stiffness at low weight.
Sectioned aluminium profiles laid out for inspection
The full profile library, sectioned — chamber counts and break widths differ per system.
Window frame corner joint with glazing and gasket
Corner joint with the glass pack in place — one continuous gasket line, concealed drainage.

Materials, specified at the line

Every material below is stated on the data sheet per project — the mill certificate for the profile, the schedule for the coating, the specification for the glass. Nothing is “equivalent or better” in the paperwork; the paperwork names the material.

Profile

6063-T5 multi-chamber extrusion, PA66-GF25 thermal-break bar, corner-bonded in the press line. Mill certificate retained per heat.

Surface

Chromate-free pre-treatment, 80–100 µm powder coat with the salt-fog schedule on coastal elevations, anodising or wood-grain film where the specification calls for them.

Glazing

Tempered, laminated or IGU to the project schedule — 0.38 SGP interlayer on impact units, 24–42 mm asymmetric laminated core on the acoustic range.

Hardware & seals

316 stainless on marine schedules, 6–12 point multi-point locks, anti-lift cam on every sash, two replaceable EPDM gasket lines with the replacement cycle published.

Six stages, one gate

  1. 01

    Extrusion & thermal break

    Multi-chamber 6063-T5 profiles; insulated bar joined and bonded in the press line.

  2. 02

    Finishing

    Anodising, powder-coating or wood-grain film; salt-fog schedule for coastal projects.

  3. 03

    Glazing

    Tempering, laminating and IGU assembly on site; acoustic and low-E schedules per specification.

  4. 04

    Sash assembly

    Factory-assembled sashes with hardware, gaskets and screens fitted and function-checked.

  5. 05

    Quality gate

    Dimensional audit, air/water/cycle spot tests and photo record before crating.

  6. 06

    Crating & loading

    Corner-protected crates, desiccant, loading report per container.

The quality gate, in numbers

Spot-tested on the rig at stage five, and the tested figure — not the nominal one — is what lands in the data sheet. Configuration targets as published on the home page.

1.4 W/m²K

U-value, tested to EN 673

3,500 Pa

Wind-load resistance, EN 12211 class

900 Pa

Water tightness, EN 1027

Class 4

Air tightness, EN 1026

45 dB

Acoustic Rw, EN ISO 10140

The ten shop-floor operations →Quality control checkpoints →Packing and container loading →

What every crate documents

The balance of payment runs against a photo report, and the report runs against the same documentation that ships in the crate. Nothing on site should be guessed.

Packing list & loading report

Unit-by-unit, per container, with the crate and pallet map.

Pre-shipment photo report

Every unit photographed at the quality gate before the balance is due.

Hardware & glass schedules

The exact lock set, hinge line and glazing unit per reference — matches the schedule.

Install guide per market

The three-zone fixing detail and sealant schedule for your building code.

Crating

Corner-protected, desiccanted, with a moisture card at the first layer.

What a buyer should verify — and where we show it

The list below is what we would ask of a supplier. Each row names the document we issue against it, so the audit takes a checklist, not a conversation.

“Is the profile the one on the data sheet?”

Mill certificate per heat, attached to the shop drawings.

“Is the coating schedule specified, not assumed?”

Coating data sheet with the salt-fog hours for your elevation, per project.

“Is the glass unit built to the schedule?”

Glazing schedule per reference — thickness, core, SGP, low-E — matched against the quotation.

“Was the rating tested on our sizes?”

Project test report (PGT for impact, EN/AS rig for performance) on the configuration we ship.

“Does the documentation follow the container?”

Packing list, loading report and pre-shipment photo report — the balance runs against them.

Prefer to talk it through?

Send a drawing or a one-line brief on WhatsApp.

+86 177 0868 3991 — quotation within 24 hours, shop drawings free in 3 working days.